Before doing any contribution read CONTRIBUTING.
If you want to buy this project online please refer to: Tindie
Email: [email protected]
General Discord: https://discord.gg/dFD5HHa
Developer Discord: https://discord.gg/rxNNHYN9EQ
Note: To use this cards you need to install HACS and the following repositories:
Note: Please use you're own entities if yours aren't equal to mine.
Weather:
type: weather-forecast
entity: weather.homePlant Monitor:
type: glance
entities:
- entity: plant.plant_1
title: 'Green House #1'Plant (plant.yaml)
Plant#1:
sensors:
moisture: sensor.green_house_1_plant_1_moisture
temperature: sensor.green_house_1_plant_1_temperature
conductivity: sensor.green_house_1_plant_1_soil_conductivity
brightness: sensor.green_house_1_plant_1_illuminance
min_moisture: 15
min_temperature: 15
min_conductivity: 350To add the plant.yaml to configuration add the following code to configuration.yaml:
plant: !include plant.yamlGreenHouse Actions/Monitor:
type: 'custom:config-template-card'
entities:
- sensor.green_house_1_temperature
- sensor.green_house_1_humidity
- sensor.green_house_1_intake_water_ph
- sensor.green_house_1_intake_water_flow
- switch.greenhouse_1_fan_1
- switch.greenhouse_1_fan_2
- sensor.green_house_1_intake_neutral_ph
variables:
INTAKE_NEUTRAL_PH: 'states["sensor.green_house_1_intake_neutral_ph"].state'
INTAKE_PH: 'states["sensor.green_house_1_intake_neutral_ph"].state'
OFFSET: 0.5
WATER_FLOW: 'states["sensor.green_house_1_intake_water_flow"].state'
card:
type: entities
entities:
- entity: sensor.green_house_1_temperature
name: Temperature
- entity: sensor.green_house_1_humidity
name: Humidity
- entity: sensor.green_house_1_intake_water_ph
name: Intake Water PH
max: '${INTAKE_NEUTRAL_PH*2}'
min: 0
entity_row: true
target: '${INTAKE_NEUTRAL_PH}'
type: 'custom:bar-card'
icon: >-
${INTAKE_PH >= INTAKE_NEUTRAL_PH - OFFSET && INTAKE_PH <=
INTAKE_NEUTRAL_PH + OFFSET ? 'mdi:water-remove' : 'mdi:water-check'}
- entity: sensor.green_house_1_intake_water_temperature
name: Intake Water Temperature
- entity: sensor.green_house_1_intake_water_flow
name: Intake Water Flow
icon: '${WATER_FLOW == 0 ? ''mdi:pipe-disconnected'' : ''mdi:pipe''}'
- entity: switch.greenhouse_1_fan_1
name: 'Fan #1'
icon: 'mdi:fan'
- entity: switch.greenhouse_1_fan_2
name: 'Fan #2'
icon: 'mdi:fan'
- entity: switch.green_house_1_intake_water
icon: 'mdi:engine'
title: 'Green House #1'Note: Feel free to change any values as long as they are the same in your dashboard so no errors occur.
Note: This code uses the Xiaomi LYWSD03MMC for mesuring temperature and humidity, the Xiaomi MiFlora to measure plant temperature, brightness, condutivity, and moisture and used some other electronics like the following:
GreenHouse Box:
esphome:
name: greenhouse_1_sensors
platform: ESP32
board: esp32dev
wifi:
ssid: "<YOUR_SSID>"
password: "<YOUR_PASSWORD>"
logger:
# Enable Home Assistant API
api:
password: "<YOUR_PASSWORD>"
ota:
password: "<YOUR_PASSWORD>"
binary_sensor:
- platform: status
name: "Green House 1 Hub Status"
esp32_ble_tracker:
switch:
- platform: gpio
pin: 25
name: "Green House 1 Intake Water"
dallas:
- pin: GPIO33
sensor:
- platform: atc_mithermometer
mac_address: "<YOUR_MAC_ADDR>"
temperature:
name: "Green House 1 Temperature"
humidity:
name: "Green House 1 Humidity"
battery_level:
name: "Green House 1 Battery Level"
- platform: xiaomi_hhccjcy01
mac_address: '<YOUR_MAC_ADDR>'
temperature:
name: "Green House 1 Plant 1 Temperature"
moisture:
name: "Green House 1 Plant 1 Moisture"
illuminance:
name: "Green House 1 Plant 1 Illuminance"
conductivity:
name: "Green House 1 Plant 1 Soil Conductivity"
- platform: adc
pin: GPIO32
id: intake_water_ph
name: "Green House 1 Intake Water PH"
icon: "mdi:water"
update_interval: 1s
unit_of_measurement: pH
attenuation: 11db
filters:
- median:
window_size: 10
send_every: 5
send_first_at: 5
- calibrate_linear:
- 3.00 -> 6.0
- 2.50 -> 9.5
- platform: dallas
address: <YOUR_ADDR>
id: intake_water_temp
name: 'Green House 1 Intake Water Temperature'
icon: "mdi:thermometer"
on_value:
then:
lambda: |-
float temp = id(intake_water_temp).state;
float in_min = 0;
float in_max = 100;
float out_min = 7.47;
float out_max = 6.14;
float neutral_pH = ((x - in_min) * (out_max - out_min) + out_min * (in_max - in_min)) / (in_max - in_min);
id(intake_neutral_ph).publish_state(neutral_pH);
char str[32];
dtostrf(neutral_pH, 8, 2, str);
ESP_LOGD("'Intake Neutral pH'", str);
- platform: adc
pin: GPIO35
id: intake_water_flow
name: "Green House 1 Intake Water Flow"
icon: "mdi:pipe-leak"
update_interval: 1s
unit_of_measurement: L/min
attenuation: 11db
filters:
- median:
window_size: 10
send_every: 5
send_first_at: 5
- platform: template
id: intake_neutral_ph
name: "Green House 1 Intake Neutral pH"Note: Our fans where not wifi controllable by default so we used a Sonoff Basic to act as the middle man and made them wifi controllable.
Fan control: (Sonoff)
esphome:
name: greenhouse_1_fan_1
platform: ESP8266
board: esp01_1m
wifi:
ssid: "<YOUR_SSID>"
password: "<YOUR_PASSWORD>"
logger:
# Enable Home Assistant API
api:
password: "<YOUR_PASSWORD>"
ota:
password: "<YOUR_PASSWORD>"
binary_sensor:
- platform: status
name: "GreenHouse #1 Fan #1 Board"
- platform: gpio
pin:
number: GPIO0
mode: INPUT_PULLUP
inverted: True
name: "GreenHouse #1 Fan #1 Button"
on_press:
- switch.toggle: relay
switch:
- platform: gpio
name: "GreenHouse #1 Fan #1"
pin: GPIO12
id: relay
status_led:
pin:
number: GPIO13
inverted: yes
Note: This projects is under development and new updates should be added with frequency.
Note: Automations will be added and created in the near future.
Note: These picturesdo not include the Water Flow Sensor and Valve