probe: remove the old eddy current support

KalicoCrew · Dec 23, 2024 · fbb3d9c · fbb3d9c
1 parent b0c0ce6
commit fbb3d9c
Show file tree

Hide file tree

Showing 10 changed files with 1 addition and 1,029 deletions.
diff --git a/docs/Config_Reference.md b/docs/Config_Reference.md
@@ -2544,43 +2544,6 @@ z_offset:
 #   See the "probe" section for more information on the parameters above.
 ```
 
-### [probe_eddy_current]
-
-Support for eddy current inductive probes. One may define this section
-(instead of a probe section) to enable this probe. See the
-[command reference](G-Codes.md#probe_eddy_current) for further information.
-
-```
-[probe_eddy_current my_eddy_probe]
-sensor_type: ldc1612
-#   The sensor chip used to perform eddy current measurements. This
-#   parameter must be provided and must be set to ldc1612.
-#intb_pin:
-#   MCU gpio pin connected to the ldc1612 sensor's INTB pin (if
-#   available). The default is to not use the INTB pin.
-#z_offset:
-#   The nominal distance (in mm) between the nozzle and bed that a
-#   probing attempt should stop at. This parameter must be provided.
-#i2c_address:
-#i2c_mcu:
-#i2c_bus:
-#i2c_software_scl_pin:
-#i2c_software_sda_pin:
-#i2c_speed:
-#   The i2c settings for the sensor chip. See the "common I2C
-#   settings" section for a description of the above parameters.
-#x_offset:
-#y_offset:
-#speed:
-#lift_speed:
-#samples:
-#sample_retract_dist:
-#samples_result:
-#samples_tolerance:
-#samples_tolerance_retries:
-#   See the "probe" section for information on these parameters.
-```
-
 ### [axis_twist_compensation]
 
 A tool to compensate for inaccurate probe readings due to twist in X gantry. See

diff --git a/docs/G-Codes.md b/docs/G-Codes.md
@@ -1197,28 +1197,6 @@ babystepping), and subtract if from the probe's z_offset.  This acts
 to take a frequently used babystepping value, and "make it permanent".
 Requires a `SAVE_CONFIG` to take effect.
 
-### [probe_eddy_current]
-
-The following commands are available when a
-[probe_eddy_current config section](Config_Reference.md#probe_eddy_current)
-is enabled.
-
-#### PROBE_EDDY_CURRENT_CALIBRATE
-`PROBE_EDDY_CURRENT_CALIBRATE CHIP=<config_name>`: This starts a tool
-that calibrates the sensor resonance frequencies to corresponding Z
-heights. The tool will take a couple of minutes to complete. After
-completion, use the SAVE_CONFIG command to store the results in the
-printer.cfg file.
-
-#### LDC_CALIBRATE_DRIVE_CURRENT
-`LDC_CALIBRATE_DRIVE_CURRENT CHIP=<config_name>` This tool will
-calibrate the ldc1612 DRIVE_CURRENT0 register. Prior to using this
-tool, move the sensor so that it is near the center of the bed and
-about 20mm above the bed surface. Run this command to determine an
-appropriate DRIVE_CURRENT for the sensor. After running this command
-use the SAVE_CONFIG command to store that new setting in the
-printer.cfg config file.
-
 ### [pwm_cycle_time]
 
 The following command is available when a

diff --git a/klippy/extras/ldc1612.py b/klippy/extras/ldc1612.py