Reduce the

ew labels to just what 3.4.0 has. Added D50 for subGHz.

docs/quick-start/transmitters/lua-howto.md

@@ -112,7 +112,7 @@ From these examples:
 
 Items with `>` before the name is a folder that when selected shows another level of customization. `TX Power`, `VTX Administrator`, `Wifi Connectivity` are examples of these items.
 
-:new: These items will now show what is currently set for the items within. An example would be on `TX Power`, which will show the current Power set, and if Dynamic Power is enabled, it will show the current set Max Power, followed by the indicator `Dyn`.
+These items will now show what is currently set for the items within. An example would be on `TX Power`, which will show the current Power set, and if Dynamic Power is enabled, it will show the current set Max Power, followed by the indicator `Dyn`.
 
 ### Packet Rate and Telemetry Ratio
 
@@ -131,16 +131,17 @@ These are shown as `Packet Rate` and `Telem Ratio` in the Lua script, which allo
 	The following options are available for `2.4GHz`:
 
 	- `50Hz, 150Hz, 250Hz & 500Hz`: Lora-based options. Higher means lower latency at the expense of sensitivity. Since v1.0.
-	- `F500 & F1000` :new: : Pure FLRC for lowest latency, reduced range compared to LoRa, 500Hz and 1000Hz. [Details](https://github.com/ExpressLRS/ExpressLRS/pull/1277)
-	- `D250 & D500` :new: : Redundant transmit FLRC modes.  `D` stands for `Déjà Vu`, 250Hz and 500Hz. Higher latency, reduced packet jitter and higher LQ. Same range as other FLRC modes. [Details](https://github.com/ExpressLRS/ExpressLRS/pull/1527)
-	- `100Hz Full & 333Hz Full` :new: : Lora-based 10-bit Full Resolution with 8ch/12ch/16 Switch Mode options. [Details](https://github.com/ExpressLRS/ExpressLRS/pull/1572)
+	- `F500 & F1000`: Pure FLRC for lowest latency, reduced range compared to LoRa, 500Hz and 1000Hz. [Details](https://github.com/ExpressLRS/ExpressLRS/pull/1277)
+	- `D250 & D500`: Redundant transmit FLRC modes.  `D` stands for `Déjà Vu`, 250Hz and 500Hz. Higher latency, reduced packet jitter and higher LQ. Same range as other FLRC modes. [Details](https://github.com/ExpressLRS/ExpressLRS/pull/1527)
+	- `100Hz Full & 333Hz Full`: Lora-based 10-bit Full Resolution with 8ch/12ch/16 Switch Mode options. [Details](https://github.com/ExpressLRS/ExpressLRS/pull/1572)
 
 	The following options are available for `900MHz`:
 
 	- `25Hz, 50Hz, 100Hz & 200Hz`: LoRa-based options. Higher means lower latency at the expense of sensitivity. Since v1.0.
-	- `100Hz Full` :new: : Lora-based 10-bit Full Resolution with 8ch/12ch/16 Switch Mode options. [Details](https://github.com/ExpressLRS/ExpressLRS/pull/1572)
+	- `100Hz Full`: Lora-based 10-bit Full Resolution with 8ch/12ch/16 Switch Mode options. [Details](https://github.com/ExpressLRS/ExpressLRS/pull/1572)
     - `250Hz` :new: : Only Available for GemX Devices. [Details here.](https://github.com/ExpressLRS/ExpressLRS/pull/2540)
     - `200Hz Full` :new: : Only Available for GemX Devices. [Details here.](https://github.com/ExpressLRS/ExpressLRS/pull/2540)
+    = `D50Hz` :new: : Lora-based Redundant transmit mode via DVDA. [Details here.](https://github.com/ExpressLRS/ExpressLRS/pull/2089)
 
     The following options are available for `GemX`:
 
@@ -156,15 +157,15 @@ These are shown as `Packet Rate` and `Telem Ratio` in the Lua script, which allo
 	Never change the packet rate while flying as this **FORCES A DISCONNECT** between the TX and RX. 
 
 * `Telem Ratio` sets the telemetry ratio or how much of the packet rate is used to send telemetry. The options, in order of increasing telemetry rate, are: `Off, 1:128, 1:64, 1:32, 1:16, 1:8, 1:4, 1:2`. A Telem Ratio of 1:64 means one out of every 64 packets are used for telemetry data.
-	- :new: v3.0 comes with `Std` and `Race` options. `Std` changes ratio depending on the Packet Rate, and `Race` is the same as Std, but will disable telemetry and sync while Armed.
+	- v3.0 comes with `Std` and `Race` options. `Std` changes ratio depending on the Packet Rate, and `Race` is the same as Std, but will disable telemetry and sync while Armed.
 
 	For information on telemetry setup, see [First Flight: Telemetry](../pre-1stflight.md#telemetry) and [Telemetry Bandwidth](../../info/telem-bandwidth.md).
 
 ### Switch Mode
 
 The Switch Mode setting controls how channels AUX1-AUX8 are sent to the receiver (the 4 main channels are always 10-bit). The options are `Hybrid & Wide`. **Hybrid** mode is 6x 2, 3 or 6-position + 1x 16-position, and **Wide** is 7x 64 or 128-position. For detail about the differences, see the [Switch Configs](../../software/switch-config.md) documentation.
 
-:new: In full resolution modes, the Switch Mode parameter selects the number of channels to be used. [Full Resolution Switch Modes](../../software/switch-config.md#full-resolution-switch-configuration-modes) 
+In full resolution modes, the Switch Mode parameter selects the number of channels to be used. [Full Resolution Switch Modes](../../software/switch-config.md#full-resolution-switch-configuration-modes) 
 
 !!! hint "Hot Tip"
 	The Switch Mode can only be changed when not connected to a receiver. The top right corner of the Lua script will show a `-` if you're not connected.