| layout | title |
|---|---|
documentation |
LZW36 - ZWave |
{% include base.html %}
This describes the Z-Wave device LZW36, manufactured by Inovelli with the thing type UID of inovelli_lzw36_00_000.
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The LZW36 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
There are two different wireless protocols that are used to make this fan & light switch - Z-Wave and RF.
Z-Wave is what gives the switch remote (smart) control, whereas RF is what connects the switch to the module. In other words, your hub/gateway connects to your switch, where you can tell it to change the speed of the fan or the brightness of the lights. From there the switch sends an RF command to the module to physically make those commands happen at the fan itself.
Enable the inclusion process on your Hub or Gateway. Hold down button A and press button B 3x quickly and your LED Bars will pulse blue signifying the switch is in inclusion mode. If successful, the switch LED Bars will flash Green and if unsuccessful, the LED Bars will flash Red.
Place your hub or gateway into exclusion mode. Then: Hold button A + Press Button B 3x. If it is successful the LED will blink green.
- Light Dimmer (and Scene Control*): This button can be used to increase or decrease the dimness level on your light. Press (hold) up to increase brightness and press (hold) down to decrease the brightness. Also, a single press will send a scene command to your hub.
- Light On/Off Button (and Scene Control*): Press this button to turn on and off the fan light(s). This button can also be used to trigger Z-Wave scenes. You may add up to 7 scenes (Tap x, 2x, 3x, 4x, 5x, Hold, Release).
- Light RGB LED Bar (with Notifications*): Shows the level at which the fan light(s) are set at. In addition, it can be used as a notifier for various events (i.e.: turn purple if front door is open).
- Fan Speed (and Scene Control*): This button can be used to increase or decrease the speed of your fan. Press (hold) up to increase the speed and press (hold) down to decrease the speed. Also, a single press will send a scene command to your hub.
- Fan On/Off Button (and Scene Control*): Press this button to turn on and off the fan. This button can also be used to trigger Z-Wave scenes. You may add up to 7 scenes (Tap x, 2x, 3x, 4x, 5x, Hold, Release).
- Light RGB LED Bar (with Notifications*): Shows the level at which the fan speed is set at. In addition, it can be used as a notifier for various events (i.e.: turn red when your alarm is armed).
- Air Gap Switch: This will reboot the switch if it needs to be rebooted (NOTE: The air-gap switch will not cut power to the module).NOT SHOWN: Energy Monitoring* and Scene Control* are built-in features of this switch as well
The following table summarises the channels available for the LZW36 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Dimmer | switch_dimmer | switch_dimmer | DimmableLight | Dimmer |
| Electric meter (watts) | meter_watts | meter_watts | Energy | Number |
| Electric meter (kWh) | meter_kwh | meter_kwh | Energy | Number |
| Scene Number | scene_number | scene_number | Number | |
| Light LED Color | config_decimal | config_decimal | Number | |
| Fan LED Color | config_decimal | config_decimal | Number | |
| Light LED Strip Effect | config_decimal | config_decimal | Number | |
| Fan LED Strip Effect [Deprecated] | config_decimal | config_decimal | Number | |
| Light Dimmer | switch_dimmer1 | switch_dimmer | DimmableLight | Dimmer |
| Fan Dimmer | switch_dimmer2 | switch_dimmer | DimmableLight | Dimmer |
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
Indicates the instantaneous power consumption.
The meter_watts channel is of type meter_watts and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the energy consumption (kWh).
The meter_kwh channel is of type meter_kwh and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Triggers when a scene button is pressed.
The scene_number channel is of type scene_number and supports the Number item.
This channel provides the scene, and the event as a decimal value in the form <scene>.<event>. The scene number is set by the device, and the event is as follows -:
| Event ID | Event Description |
|---|---|
| 0 | Single key press |
| 1 | Key released |
| 2 | Key held down |
| 3 | Double keypress |
| 4 | Tripple keypress |
| 5 | 4 x keypress |
| 6 | 5 x keypress |
This is the color of the Light LED strip represented as part of the HUE color wheel. Since the wheel has 360 values and this parameter only has 255, the following equation can be used to determine the color: value/255 * 360 = Hue color wheel value
Generic class for configuration parameter.
The config_decimal channel is of type config_decimal and supports the Number item.
This is the color of the Fan LED strip represented as part of the HUE color wheel. Since the wheel has 360 values and this parameter only has 255, the following equation can be used to determine the color: value/255 * 360 = Hue color wheel value
Generic class for configuration parameter.
The config_decimal channel is of type config_decimal and supports the Number item.
Calculator available at: http://calculator.inovelli.com/
Generic class for configuration parameter.
The config_decimal channel is of type config_decimal and supports the Number item.
Calculator available at: http://calculator.inovelli.com/
Generic class for configuration parameter.
The config_decimal channel is of type config_decimal and supports the Number item.
Note: This channel is marked as deprecated so should not be used.
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer1 channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer2 channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
The following table provides a summary of the 39 configuration parameters available in the LZW36. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Light Dimming Speed | Light Dimming Speed |
| 2 | Light Dimming Speed (From Switch) | Light Dimming Speed (From Switch) |
| 3 | Light Ramp Rate | Light Ramp Rate |
| 4 | Light Ramp Rate (From Switch) | Light Ramp Rate (From Switch) |
| 5 | Minimum Light Level | Minimum Light Level |
| 6 | Maximum Light Level | Maximum Light Level |
| 7 | Minimum Fan Level | Minimum Fan Level |
| 8 | Maximum Fan Level | Maximum Fan Level |
| 10 | Auto Off Light Timer | Auto Off Light Timer |
| 11 | Auto Off Fan Timer | Auto Off Fan Timer |
| 12 | Default Light Level (Local) | Default Light Level (Local) |
| 13 | Default Light Level (Z-Wave) | Default Light Level (Z-Wave) |
| 14 | Default Fan Level (Local) | Default Fan Level (Local) |
| 15 | Default Fan Level (Z-Wave) | Default Fan Level (Z-Wave) |
| 16 | Light State After Power Restored | Light State After Power Restored |
| 17 | Fan State After Power Restored | Fan State After Power Restored |
| 18 | Light LED Indicator Color | Light LED Indicator Color |
| 19 | Light LED Strip Intensity | Light LED Strip Intensity |
| 20 | Fan LED Indicator Color | Fan LED Indicator Color |
| 21 | Fan LED Strip Intensity | Fan LED Strip Intensity |
| 22 | Light LED Strip Intensity (When OFF) | Light LED Strip Intensity (When OFF) |
| 23 | Fan LED Strip Intensity (When OFF) | Fan LED Strip Intensity (When OFF) |
| 24 | Light LED Strip Effect | Light LED Strip Effect |
| 24 | Light LED Strip Effect Color | Light LED Strip Effect Color |
| 24 | Light LED Strip Effect Intensity | Light LED Strip Effect Intensity |
| 24 | Light LED Strip Effect Duration | Light LED Strip Effect Duration |
| 24 | Light LED Strip Effect Type | Light LED Strip Effect Type |
| 25 | Fan LED Strip Effect | Fan LED Strip Effect |
| 25 | Fan LED Strip Effect Color | Fan LED Strip Effect Color |
| 25 | Fan LED Strip Effect Intesity | Fan LED Strip Effect Intesity |
| 25 | Fan LED Strip Effect Duration | Fan LED Strip Effect Duration |
| 25 | Fan LED Strip Effect Type | Fan LED Strip Effect Type |
| 26 | Light LED Strip Timeout | Light LED Strip Timeout |
| 27 | Fan LED Strip Timeout | Fan LED Strip Timeout |
| 28 | Active Power Reports | Active Power Reports |
| 29 | Periodic Power & Energy Reports | Periodic Power & Energy Reports |
| 30 | Energy Reports | Energy Reports |
| 31 | Local Protection Settings | Local Protection Settings |
| 51 | Enable instant on | Disable the 700ms delay. |
Light Dimming Speed This changes the speed in which the attached light dims up or down. A setting of 0 should turn the light immediately on or off (almost like an on/off switch). Increasing the value should slow down the transition speed. Values in the range 0 to 98 may be set.
The manufacturer defined default value is 4.
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Light Dimming Speed (From Switch) This changes the speed in which the attached light dims up or down when controlled from the physical switch. A setting of 0 should turn the light immediately on or off (almost like an on/off switch). Increasing the value should slow down the transition speed. A setting of 99 should keep this in sync with parameter 1. Values in the range 0 to 99 may be set.
The manufacturer defined default value is 99.
This parameter has the configuration ID config_2_1 and is of type INTEGER.
Light Ramp Rate This changes the speed in which the attached light turns on or off. For example, when a user sends the switch a basicSet(value: 0xFF) or basicSet(value: 0x00), this is the speed in which those actions take place. A setting of 0 should turn the light immediately on or off (almost like an on/off switch). Increasing the value should slow down the transition speed. A setting of 99 should keep this in sync with parameter 1. Values in the range 0 to 99 may be set.
The manufacturer defined default value is 99.
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Light Ramp Rate (From Switch) This changes the speed in which the attached light turns on or off from the physical switch. For example, when a user presses the up or down button, this is the speed in which those actions take place. A setting of 0 should turn the light immediately on or off (almost like an on/off switch). Increasing the value should slow down the transition speed. A setting of 99 should keep this in sync with parameter 1. Values in the range 0 to 99 may be set.
The manufacturer defined default value is 99.
This parameter has the configuration ID config_4_1 and is of type INTEGER.
Minimum Light Level The minimum level that the dimmer allows the bulb to be dimmed to. Useful when the user has an LED bulb that does not turn on or flickers at a lower level. Values in the range 1 to 45 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_5_1 and is of type INTEGER.
Maximum Light Level The maximum level that the dimmer allows the bulb to be dimmed to. Useful when the user has an LED bulb that reaches its maximum level before the dimmer value of 99. Values in the range 55 to 99 may be set.
The manufacturer defined default value is 99.
This parameter has the configuration ID config_6_1 and is of type INTEGER.
Minimum Fan Level The minimum level that the dimmer allows the fan to be dimmed to. Useful when the user has a fan that does not turn at a lower level. Values in the range 1 to 45 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_7_1 and is of type INTEGER.
Maximum Fan Level The maximum level that the dimmer allows the fan to be dimmed to. Values in the range 55 to 99 may be set.
The manufacturer defined default value is 99.
This parameter has the configuration ID config_8_1 and is of type INTEGER.
Auto Off Light Timer Automatically turns the light switch off after this many seconds. When the switch is turned on a timer is started that is the duration of this setting. When the timer expires, the switch is turned off. Values in the range 0 to 32767 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_10_2 and is of type INTEGER.
Auto Off Fan Timer Automatically turns the fan switch off after this many seconds. When the switch is turned on a timer is started that is the duration of this setting. When the timer expires, the switch is turned off. Values in the range 0 to 32767 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_11_2 and is of type INTEGER.
Default Light Level (Local) Default level for the dimmer when it is powered on from the local switch. A setting of 0 means that the switch will return to the level that it was on before it was turned off. Values in the range 0 to 99 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_12_1 and is of type INTEGER.
Default Light Level (Z-Wave) Default level for the dimmer when it is powered on from a Z-Wave command. A setting of 0 means that the switch will return to the level that it was on before it was turned off. Values in the range 0 to 99 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_13_1 and is of type INTEGER.
Default Fan Level (Local) Default level for the fan dimmer when it is powered on from the local switch. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Last State |
| 33 | Low |
| 66 | Medium |
| 99 | High |
The manufacturer defined default value is 0 (Last State).
This parameter has the configuration ID config_14_1 and is of type INTEGER.
Default Fan Level (Z-Wave)
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Last State |
| 33 | Low |
| 66 | Medium |
| 99 | High |
The manufacturer defined default value is 0 (Last State).
This parameter has the configuration ID config_15_1 and is of type INTEGER.
Light State After Power Restored The state the switch should return to once power is restored after power failure. 0 = off, 1-99 = level, 100=previous. Values in the range 0 to 100 may be set.
The manufacturer defined default value is 100.
This parameter has the configuration ID config_16_1 and is of type INTEGER.
Fan State After Power Restored The state the switch should return to once power is restored after power failure. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Off |
| 33 | Low |
| 66 | Medium |
| 99 | High |
| 100 | Previous State |
The manufacturer defined default value is 0 (Off).
This parameter has the configuration ID config_17_1 and is of type INTEGER.
Light LED Indicator Color This is the color of the Light LED strip represented as part of the HUE color wheel. Since the wheel has 360 values and this parameter only has 255, the following equation can be used to determine the color: value/255 * 360 = Hue color wheel value Values in the range 0 to 255 may be set.
The manufacturer defined default value is 170.
This parameter has the configuration ID config_18_2 and is of type INTEGER.
Light LED Strip Intensity This is the intensity of the Light LED strip. Values in the range 0 to 10 may be set.
The manufacturer defined default value is 5.
This parameter has the configuration ID config_19_1 and is of type INTEGER.
Fan LED Indicator Color This is the color of the Fan LED strip represented as part of the HUE color wheel. Since the wheel has 360 values and this parameter only has 255, the following equation can be used to determine the color: value/255 * 360 = Hue color wheel value Values in the range 0 to 255 may be set.
The manufacturer defined default value is 170.
This parameter has the configuration ID config_20_2 and is of type INTEGER.
Fan LED Strip Intensity This is the intensity of the Fan LED strip. Values in the range 0 to 10 may be set.
The manufacturer defined default value is 5.
This parameter has the configuration ID config_21_1 and is of type INTEGER.
Light LED Strip Intensity (When OFF) This is the intensity of the Light LED strip when the switch is off. This is useful for users to see the light switch location when the lights are off. Values in the range 0 to 10 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_22_1 and is of type INTEGER.
Fan LED Strip Intensity (When OFF) This is the intensity of the Light LED strip when the switch is off. This is useful for users to see the light switch location when the lights are off. Values in the range 0 to 10 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_23_1 and is of type INTEGER.
Light LED Strip Effect Byte 4: Effect - 0 = Off, 1 = Solid, 2 = Slow Blink, 3 = Fast Blink, 4 = Chase, 5 = Pulse
Byte 3: Duration
- 1 to 60 = 1 to 60 seconds
- 61 to 120 = 1 to 60 minutes
- 121 - 254 = 1 - 134 hours
- 255 = Indefinitely
Byte 2: Intensity - 0 to 9. 0 = dim, 9 = bright
Byte 1: Color - 0 - 255. Hue color wheel. value/255 * 360 = Hue color wheel value
Calculator available at: http://calculator.inovelli.com/This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 100600319 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_24_4 and is of type INTEGER.
Light LED Strip Effect Color Hue color wheel. value/255 * 360 = Hue color wheel value Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_24_4_000000FF and is of type INTEGER.
Light LED Strip Effect Intensity 0 = dim, 9 = bright Values in the range 0 to 9 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_24_4_0000FF00 and is of type INTEGER.
Light LED Strip Effect Duration
- 1 to 60 = 1 to 60 seconds
- 61 to 120 = 1 to 60 minutes
- 121 to 254 = 1 to 134 hours
- 255 = Indefinitely Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_24_4_00FF0000 and is of type INTEGER.
Light LED Strip Effect Type 0 = Off, 1 = Solid, 2 = Slow Blink, 3 = Fast Blink, 4 = Chase, 5 = Pulse The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Off |
| 1 | Solid |
| 2 | Slow Blink |
| 3 | Fast Blink |
| 4 | Chase |
| 5 | Pulse |
The manufacturer defined default value is 0 (Off).
This parameter has the configuration ID config_24_4_07000000 and is of type INTEGER.
Fan LED Strip Effect Byte 4: Effect - 0 = Off, 1 = Solid, 2 = Slow Blink, 3 = Fast Blink, 4 = Chase, 5 = Pulse
Byte 3: Duration
- 1 to 60 = 1 to 60 seconds
- 61 to 120 = 1 to 60 minutes
- 121 - 254 = 1 - 134 hours
- 255 = Indefinitely
Byte 2: Intensity - 0 to 9. 0 = dim, 9 = bright
Byte 1: Color - 0 - 255. Hue color wheel. value/255 * 360 = Hue color wheel value
Calculator available at: http://calculator.inovelli.com/This is an advanced parameter and will therefore not show in the user interface without entering advanced mode. Values in the range 0 to 100600319 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_25_4 and is of type INTEGER.
Fan LED Strip Effect Color Hue color wheel. value/255 * 360 = Hue color wheel value Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_25_4_000000FF and is of type INTEGER.
Fan LED Strip Effect Intesity 0 = dim, 9 = bright Values in the range 0 to 9 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_25_4_0000FF00 and is of type INTEGER.
Fan LED Strip Effect Duration
- 1 to 60 = 1 to 60 seconds
- 61 to 120 = 1 to 60 minutes
- 121 to 254 = 1 to 134 hours
- 255 = Indefinitely Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_25_4_00FF0000 and is of type INTEGER.
Fan LED Strip Effect Type 0 = Off, 1 = Solid, 2 = Slow Blink, 3 = Fast Blink, 4 = Chase, 5 = Pulse The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Off |
| 1 | Solid |
| 2 | Slow Blink |
| 3 | Fast Blink |
| 4 | Chase |
| 5 | Pulse |
The manufacturer defined default value is 0 (Off).
This parameter has the configuration ID config_25_4_07000000 and is of type INTEGER.
Light LED Strip Timeout When the LED strip is disabled (Light LED Strip Intensity is set to 0), this setting allows the LED strip to turn on temporarily while being adjusted. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Stay Off |
| 1 | One Second |
| 2 | Two Seconds |
| 3 | Three Seconds |
| 4 | Four Seconds |
| 5 | Five Seconds |
| 6 | Six Seconds |
| 7 | Seven Seconds |
| 8 | Eight Seconds |
| 9 | Nine Seconds |
| 10 | Ten Seconds |
The manufacturer defined default value is 3 (Three Seconds).
This parameter has the configuration ID config_26_1 and is of type INTEGER.
Fan LED Strip Timeout When the LED strip is disabled (Fan LED Strip Intensity is set to 0), this setting allows the LED strip to turn on temporarily while being adjusted. The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Stay Off |
| 1 | One Second |
| 2 | Two Seconds |
| 3 | Three Seconds |
| 4 | Four Seconds |
| 5 | Five Seconds |
| 6 | Six Seconds |
| 7 | Seven Seconds |
| 8 | Eight Seconds |
| 9 | Nine Seconds |
| 10 | Ten Seconds |
The manufacturer defined default value is 3 (Three Seconds).
This parameter has the configuration ID config_27_1 and is of type INTEGER.
Active Power Reports The power level change that will result in a new power report being sent. The value is a percentage of the previous report. 0 = disabled. Values in the range 0 to 100 may be set.
The manufacturer defined default value is 10.
This parameter has the configuration ID config_28_1 and is of type INTEGER.
Periodic Power & Energy Reports Time period between consecutive power and energy reports being sent (in seconds). The timer is reset after each report is sent. Values in the range 0 to 32767 may be set.
The manufacturer defined default value is 3600.
This parameter has the configuration ID config_29_2 and is of type INTEGER.
Energy Reports The energy level change that will result in a new energy report being sent. The value is a percentage of the previous report. Values in the range 0 to 100 may be set.
The manufacturer defined default value is 10.
This parameter has the configuration ID config_30_1 and is of type INTEGER.
Local Protection Settings Enable local protection on these buttons.
0 = None, 1 = Light, 2 = Fan, 3 = Both The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | None |
| 1 | Light Button |
| 2 | Fan Button |
| 3 | Both Buttons |
The manufacturer defined default value is 0 (None).
This parameter has the configuration ID config_31_1 and is of type INTEGER.
Disable the 700ms delay. Enable instant on (ie: disable the 700ms delay). Note, if you disable the delay, it will also disable scene control except for Button 1 (ie: tap up 1x or tap down 1x, held & released) and button 6, 7, 8, 9 (level up / down buttons). All other scenes will be disabled.
Firmware v1.36 and above. Values in the range 0 to 1 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_51_1 and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The LZW36 supports 7 association groups.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. Members of this group will receive unsolicited messages related to the status of the switch.
Association group 1 supports 5 nodes.
Basic Set Light Sends On & Off commands to associated devices. (1. Single press UP button sends BasicSet (0xFF) and 2. Single press Down sends BasicSet (0x00)
Association group 2 supports 5 nodes.
Switch MultiLevel Set Light Sends set level commands to associated devices when switch is pressed. (1. Hold & Release Up or Down button sends SwitchMultiLevelSet which keeps associated devices in sync with this device. 2. Single press Up button sends SwitchMultiLevelSet(0xFF) and 3. Single press Down button sends SwitchMultiLevelSet(0x00
Association group 3 supports 5 nodes.
Switch_MultiLevel_Start/Stop_Light Sends start / stop level change to associated devices.(1. Hold Up button sends SW_MULTILEVEL_START_LEVEL_CHANGE (Up) 2: Hold Down button sends SW_MULTILEVEL_START_LEVEL_CHANGE (Down) 3. Release Either button sends SW_MULTILEVEL_STOP_LEVEL_CHANGE
Association group 4 supports 5 nodes.
Basic Set Fan Sends On & Off commands to associated devices. (1. Single press UP button sends BasicSet (0xFF) and 2. Single press Down sends BasicSet (0x00)
Association group 5 supports 5 nodes.
Switch MultiLevel Set Fan Sends set level commands to associated devices when switch is pressed. (1. Hold & Release Up or Down button sends SwitchMultiLevelSet which keeps associated devices in sync with this device. 2. Single press Up button sends SwitchMultiLevelSet(0xFF) and 4. Single press Down button sends SwitchMultiLevelSet(0x00)
Association group 6 supports 5 nodes.
Switch MultiLevel Start/Stop Fan Sends start / stop level change to associated devices.(1. Hold Up button sends SW_MULTILEVEL_START_LEVEL_CHANGE (Up) 2: Hold Down button sends SW_MULTILEVEL_START_LEVEL_CHANGE (Down) 3. Release Either button sends SW_MULTILEVEL_STOP_LEVEL_CHANGE
Association group 7 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_APPLICATION_STATUS_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V3 | Linked to BASIC |
| COMMAND_CLASS_METER_V3 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_CENTRAL_SCENE_V3 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_MULTI_CHANNEL_V2 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_PROTECTION_V2 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_INDICATOR_V3 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 | |
| COMMAND_CLASS_SECURITY_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V3 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 | |
| COMMAND_CLASS_SECURITY_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V3 | Linked to BASIC |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 | |
| COMMAND_CLASS_SECURITY_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.