| layout | title |
|---|---|
documentation |
GE 28169 / Jasco 28168 - ZWave |
{% include base.html %}
This describes the Z-Wave device GE 28169 / Jasco 28168, manufactured by Jasco Products with the thing type UID of ge_28169_00_000.
This version of the device is limited to firmware versions below 4.9
The device is in the category of Power Outlet, defining Small devices to be plugged into a power socket in a wall which stick there.
The GE 28169 / Jasco 28168 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Z-wave controlled AC outlet for standard incandescent lighting, CFL/LEDs, fans or small appliances.
Must not exceed 600 watts (Incandescent); 1800W (15A) Resistive or ½ HP Motor
Put controller into inclusion mode, single press and release the manual/program button on the smart switch to include it in the network
Put controller into exclusion mode, single press and release the manual/program button on the smart switch to exclude it from the network
The following table summarises the channels available for the GE 28169 / Jasco 28168 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Switch | switch_binary | switch_binary | Switch | Switch |
| Scene Number | scene_number | scene_number | Number |
Switch the power on and off.
The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.
Triggers when a scene button is pressed.
The scene_number channel is of type scene_number and supports the Number item.
The following table provides a summary of the 1 configuration parameters available in the GE 28169 / Jasco 28168. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 3 | LED Light | Set the state of the LED Light |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
Set the state of the LED Light
The following option values may be configured, in addition to values in the range 0 to 2 -:
| Value | Description |
|---|---|
| 0 | LED Light on when Z-Wave turned OFF (Default) |
| 1 | LED Light on when Z-Wave turned On |
| 2 | LED Light Always Off |
The manufacturer defined default value is 0 (LED Light on when Z-Wave turned OFF (Default)).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The GE 28169 / Jasco 28168 supports 1 association group.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. Z-Wave Plus Lifeline
Association group 1 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_SCENE_ACTIVATION_V1 | |
| COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1 | |
| COMMAND_CLASS_CRC_16_ENCAP_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.