| layout | title |
|---|---|
documentation |
WS-100 - ZWave |
{% include base.html %}
This describes the Z-Wave device WS-100, manufactured by Dragon Tech Industrial, Ltd. with the thing type UID of dragontech_ws100_00_000.
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The WS-100 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
FEATURES
- Works with incandescent, florescent (CFL), or LED lighting and appliance
- ON/OFF status and location LED indicator
- Can be controlled wirelessly or manually
- Fits into standard single or multiple gang junction box and standard wall plates
- Decorative keypad can be replaced manually to match color with other wall switches
- Over-‐The-‐Air firmware upgrade available with compatible gateway, Z-‐Wave® static controller, PC and software
- Z-‐Wave 500 Series module inside
- Internal resettable fuse to protect from surge current
- manual reset capability
Single click and release the rocker switch
Single click and release the rocker switch
The following table summarises the channels available for the WS-100 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Switch | switch_binary | switch_binary | Switch | Switch |
| Scene Number | scene_number | scene_number | Number |
Switch the power on and off.
The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.
Triggers when a scene button is pressed.
The scene_number channel is of type scene_number and supports the Number item.
This channel provides the scene, and the event as a decimal value in the form <scene>.<event>. The scene number is set by the device, and the event is as follows -:
| Event ID | Event Description |
|---|---|
| 0 | Single key press |
| 1 | Key released |
| 2 | Key held down |
| 3 | Double keypress |
| 4 | Tripple keypress |
| 5 | 4 x keypress |
| 6 | 5 x keypress |
The following table provides a summary of the 2 configuration parameters available in the WS-100. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 3 | LED Indicator | Controls LED behavior when switch state is on/off |
| 4 | Orientation | Controls the on/off orientation of the rocker switch |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
Controls LED behavior when switch state is on/off
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | off/on |
| 1 | on/off |
| 2 | Off |
The manufacturer defined default value is 0 (off/on).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Controls the on/off orientation of the rocker switch
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Normal |
| 1 | Inverted |
The manufacturer defined default value is 0 (Normal).
This parameter has the configuration ID config_4_1 and is of type INTEGER.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The WS-100 supports 1 association group.
Association group 1 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_CENTRAL_SCENE_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.