Error using mex (line 206) Unable to complete successfully. #21
Comments
|
Hi Sepher, the kit installation routines simply set some paths and make
sure that you have all the required files and folders in your path. Then,
tries to compile some MEX C lang. routines into binaries. Unfortunately,
the MEX compiler was not properly included in the last Matlab versions I
used (2011, 12 and 13) and required some extra installation, you can google
how to set up the MEX compiler. For this reason, I included several
pre-compiled binaries, so, sometimes this message is just a warning, cause
the kit already works, you can try some examples in the example folder.
Good luck,
M.
El dom, 25 dic 2022 a la(s) 17:58, Sepehr Kalanaki ***@***.***)
escribió:
… [image: image]
<https://user-images.githubusercontent.com/101628099/209481784-32ef4227-99a0-43e2-893f-e107c3e6d40b.png>
Unfortunately I can not install the kit properly!
I face these errors!!
please help me
Error using mex (line 206)
Unable to complete successfully.
Error in InstallECGkit (line 204)
eval(['mex -outdir ''' common_path ''' ''' [common_path
source_files(ii).name] '''']);
—
Reply to this email directly, view it on GitHub
<#21>, or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ABBRMNHGM4IY6YCZDCFWDO3WPCYRHANCNFSM6AAAAAATJFEYJQ>
.
You are receiving this because you are subscribed to this thread.Message
ID: ***@***.***>
|
|
Thank you for your answer.
I installed matlab 2013 and then installed visual studio 2010 professional
and then ran the mex -setup command on matlab. The corresponding compiler
got installed and after that the kit got installed completely without any
errors as well!
[image: Mailtrack]
<https://mailtrack.io?utm_source=gmail&utm_medium=signature&utm_campaign=signaturevirality11&>
Sender
notified by
Mailtrack
<https://mailtrack.io?utm_source=gmail&utm_medium=signature&utm_campaign=signaturevirality11&>
12/27/22,
11:33:20 PM
…On Tue, Dec 27, 2022 at 4:12 PM Mariano Llamedo ***@***.***> wrote:
Hi Sepher, the kit installation routines simply set some paths and make
sure that you have all the required files and folders in your path. Then,
tries to compile some MEX C lang. routines into binaries. Unfortunately,
the MEX compiler was not properly included in the last Matlab versions I
used (2011, 12 and 13) and required some extra installation, you can google
how to set up the MEX compiler. For this reason, I included several
pre-compiled binaries, so, sometimes this message is just a warning, cause
the kit already works, you can try some examples in the example folder.
Good luck,
M.
El dom, 25 dic 2022 a la(s) 17:58, Sepehr Kalanaki ***@***.***)
escribió:
> [image: image]
> <
https://user-images.githubusercontent.com/101628099/209481784-32ef4227-99a0-43e2-893f-e107c3e6d40b.png
>
> Unfortunately I can not install the kit properly!
>
> I face these errors!!
> please help me
>
> Error using mex (line 206)
> Unable to complete successfully.
>
> Error in InstallECGkit (line 204)
> eval(['mex -outdir ''' common_path ''' ''' [common_path
> source_files(ii).name] '''']);
>
> —
> Reply to this email directly, view it on GitHub
> <#21>, or unsubscribe
> <
https://github.com/notifications/unsubscribe-auth/ABBRMNHGM4IY6YCZDCFWDO3WPCYRHANCNFSM6AAAAAATJFEYJQ
>
> .
> You are receiving this because you are subscribed to this thread.Message
> ID: ***@***.***>
>
—
Reply to this email directly, view it on GitHub
<#21 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AYHLRQ5PPINCLHQWPR7JUCDWPLP2RANCNFSM6AAAAAATJFEYJQ>
.
You are receiving this because you authored the thread.Message ID:
***@***.***>
|
|
Glad to hear that! thanks.
El mar, 27 dic 2022 a la(s) 17:06, Sepehr Kalanaki ***@***.***)
escribió:
… Thank you for your answer.
I installed matlab 2013 and then installed visual studio 2010 professional
and then ran the mex -setup command on matlab. The corresponding compiler
got installed and after that the kit got installed completely without any
errors as well!
[image: Mailtrack]
<
https://mailtrack.io?utm_source=gmail&utm_medium=signature&utm_campaign=signaturevirality11&
>
Sender
notified by
Mailtrack
<
https://mailtrack.io?utm_source=gmail&utm_medium=signature&utm_campaign=signaturevirality11&
>
12/27/22,
11:33:20 PM
On Tue, Dec 27, 2022 at 4:12 PM Mariano Llamedo ***@***.***>
wrote:
> Hi Sepher, the kit installation routines simply set some paths and make
> sure that you have all the required files and folders in your path. Then,
> tries to compile some MEX C lang. routines into binaries. Unfortunately,
> the MEX compiler was not properly included in the last Matlab versions I
> used (2011, 12 and 13) and required some extra installation, you can
google
> how to set up the MEX compiler. For this reason, I included several
> pre-compiled binaries, so, sometimes this message is just a warning,
cause
> the kit already works, you can try some examples in the example folder.
>
> Good luck,
> M.
>
> El dom, 25 dic 2022 a la(s) 17:58, Sepehr Kalanaki ***@***.***)
> escribió:
>
> > [image: image]
> > <
>
https://user-images.githubusercontent.com/101628099/209481784-32ef4227-99a0-43e2-893f-e107c3e6d40b.png
> >
> > Unfortunately I can not install the kit properly!
> >
> > I face these errors!!
> > please help me
> >
> > Error using mex (line 206)
> > Unable to complete successfully.
> >
> > Error in InstallECGkit (line 204)
> > eval(['mex -outdir ''' common_path ''' ''' [common_path
> > source_files(ii).name] '''']);
> >
> > —
> > Reply to this email directly, view it on GitHub
> > <#21>, or unsubscribe
> > <
>
https://github.com/notifications/unsubscribe-auth/ABBRMNHGM4IY6YCZDCFWDO3WPCYRHANCNFSM6AAAAAATJFEYJQ
> >
> > .
> > You are receiving this because you are subscribed to this
thread.Message
> > ID: ***@***.***>
> >
>
> —
> Reply to this email directly, view it on GitHub
> <#21 (comment)>,
> or unsubscribe
> <
https://github.com/notifications/unsubscribe-auth/AYHLRQ5PPINCLHQWPR7JUCDWPLP2RANCNFSM6AAAAAATJFEYJQ
>
> .
> You are receiving this because you authored the thread.Message ID:
> ***@***.***>
>
—
Reply to this email directly, view it on GitHub
<#21 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ABBRMNCPJ45TQE33QTAFRJ3WPND3ZANCNFSM6AAAAAATJFEYJQ>
.
You are receiving this because you commented.Message ID:
***@***.***>
|
|
Dear dr.Llamedo
*sorry to bother you again!*
*I wanted to know the ECG-kit's strengths and weaknesses from your point of
view because you have actually created this amazing kit!*
I need to know the pros and cons of this kit for my final project of
Biomedical signal processing course at University.
sincerely
Sepehr Kalanaki
[image: Mailtrack]
<https://mailtrack.io?utm_source=gmail&utm_medium=signature&utm_campaign=signaturevirality11&>
Sender
notified by
Mailtrack
<https://mailtrack.io?utm_source=gmail&utm_medium=signature&utm_campaign=signaturevirality11&>
01/25/23,
11:39:12 PM
On Wed, Dec 28, 2022 at 1:50 PM Mariano Llamedo ***@***.***>
wrote:
… Glad to hear that! thanks.
El mar, 27 dic 2022 a la(s) 17:06, Sepehr Kalanaki ***@***.***)
escribió:
> Thank you for your answer.
> I installed matlab 2013 and then installed visual studio 2010
professional
> and then ran the mex -setup command on matlab. The corresponding compiler
> got installed and after that the kit got installed completely without any
> errors as well!
>
>
>
>
> [image: Mailtrack]
> <
>
https://mailtrack.io?utm_source=gmail&utm_medium=signature&utm_campaign=signaturevirality11&
> >
> Sender
> notified by
> Mailtrack
> <
>
https://mailtrack.io?utm_source=gmail&utm_medium=signature&utm_campaign=signaturevirality11&
> >
> 12/27/22,
> 11:33:20 PM
>
> On Tue, Dec 27, 2022 at 4:12 PM Mariano Llamedo ***@***.***>
> wrote:
>
> > Hi Sepher, the kit installation routines simply set some paths and make
> > sure that you have all the required files and folders in your path.
Then,
> > tries to compile some MEX C lang. routines into binaries.
Unfortunately,
> > the MEX compiler was not properly included in the last Matlab versions
I
> > used (2011, 12 and 13) and required some extra installation, you can
> google
> > how to set up the MEX compiler. For this reason, I included several
> > pre-compiled binaries, so, sometimes this message is just a warning,
> cause
> > the kit already works, you can try some examples in the example folder.
> >
> > Good luck,
> > M.
> >
> > El dom, 25 dic 2022 a la(s) 17:58, Sepehr Kalanaki ***@***.***)
> > escribió:
> >
> > > [image: image]
> > > <
> >
>
https://user-images.githubusercontent.com/101628099/209481784-32ef4227-99a0-43e2-893f-e107c3e6d40b.png
> > >
> > > Unfortunately I can not install the kit properly!
> > >
> > > I face these errors!!
> > > please help me
> > >
> > > Error using mex (line 206)
> > > Unable to complete successfully.
> > >
> > > Error in InstallECGkit (line 204)
> > > eval(['mex -outdir ''' common_path ''' ''' [common_path
> > > source_files(ii).name] '''']);
> > >
> > > —
> > > Reply to this email directly, view it on GitHub
> > > <#21>, or unsubscribe
> > > <
> >
>
https://github.com/notifications/unsubscribe-auth/ABBRMNHGM4IY6YCZDCFWDO3WPCYRHANCNFSM6AAAAAATJFEYJQ
> > >
> > > .
> > > You are receiving this because you are subscribed to this
> thread.Message
> > > ID: ***@***.***>
> > >
> >
> > —
> > Reply to this email directly, view it on GitHub
> > <#21 (comment)
>,
> > or unsubscribe
> > <
>
https://github.com/notifications/unsubscribe-auth/AYHLRQ5PPINCLHQWPR7JUCDWPLP2RANCNFSM6AAAAAATJFEYJQ
> >
> > .
> > You are receiving this because you authored the thread.Message ID:
> > ***@***.***>
> >
>
> —
> Reply to this email directly, view it on GitHub
> <#21 (comment)>,
> or unsubscribe
> <
https://github.com/notifications/unsubscribe-auth/ABBRMNCPJ45TQE33QTAFRJ3WPND3ZANCNFSM6AAAAAATJFEYJQ
>
> .
> You are receiving this because you commented.Message ID:
> ***@***.***>
>
—
Reply to this email directly, view it on GitHub
<#21 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AYHLRQ4LJHSDX74EDH2YP7DWPQH6HANCNFSM6AAAAAATJFEYJQ>
.
You are receiving this because you authored the thread.Message ID:
***@***.***>
|
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Unfortunately I can not install the kit properly!
I face these errors!!
please help me
Error using mex (line 206)
Unable to complete successfully.
Error in InstallECGkit (line 204)
eval(['mex -outdir ''' common_path ''' ''' [common_path source_files(ii).name] '''']);
The text was updated successfully, but these errors were encountered: