Huawei4850 mit CAN Bus

[tstrempel1980]

Hallo zusammen,
ich nutze das CAN Joly Board, Pin mapping habe ich angepasst. Jumper gesetzt.
Der Laderegler soll den Marstek B2500 laden.
Die Entladung abends erfolgt über den HM-600.
OpenDTU on Battery Version: 2025.01.23

warum wird der Laderegler nicht aktiviert?
Ich habe über einen längeren Zeitraum -300 Watt.
Und was bedeutet "disable PSU"

[DPL] requesting 0 W from 0 battery-powered inverters currently producing 0 W (diff 0 W, hysteresis 5 W)
11:23:22.616 > [DPL inverter 114184518511]:
11:23:22.682 > solar-powered, producing 43 W
11:23:22.743 > lower/current/upper limit: 50/49/600 W, output capability: 600 W
11:23:22.810 > sending commands enabled, reachable, eligible
11:23:22.869 > max reduction production/standby: 0/0 W, max increase: 0 W
11:23:22.936 > target limit/output/state: -1 W (unchanged)/43 W/unchanged, 0 update timeouts
11:23:22.999 > MPPTs AC power: a: 21 W b: 23 W
11:23:23.058 > Fetch inverter: 114184518511
11:23:23.123 > Queue size - NRF: 1 CMT: 0
11:23:23.186 > Last missing
11:23:23.248 > Request retransmit: 3
11:23:23.313 > Middle missing
11:23:23.479 > Request retransmit: 1
11:23:23.533 > [Huawei::Controller] Inverter is active, disable PSU
11:23:23.685 > [Huawei::HwIfc] [60.452] InputTemperature: 24.00°C
11:23:23.735 > [Huawei::HwIfc] [60.451] OutputTemperature: 23.00°C
11:23:23.788 > [Huawei::HwIfc] [60.450] InputVoltage: 231.34V
11:23:23.845 > [Huawei::HwIfc] [60.448] OutputCurrentMax: 0.00A
11:23:23.894 > [Huawei::HwIfc] [60.442] InputFrequency: 50.03Hz
11:23:23.964 > [Huawei::HwIfc] [60.453] OutputCurrent: 0.00A
11:23:24.025 > [Huawei::HwIfc] [60.441] InputPower: 0.00W
11:23:24.083 > [Huawei::HwIfc] [60.443] InputCurrent: 0.00A
11:23:24.146 > [Huawei::HwIfc] [60.445] OutputPower: 0.00W
11:23:24.217 > [Huawei::HwIfc] [60.446] Efficiency: 0.00
11:23:24.272 > [Huawei::HwIfc] [60.447] OutputVoltage: 1.77V
11:23:24.335 > Middle missing
11:23:24.399 > Request retransmit: 1
11:23:24.460 > Middle missing
11:23:24.540 > Request retransmit: 1
11:23:24.603 > Fetch inverter: 114184518511
11:23:24.665 > Queue size - NRF: 1 CMT: 0
11:23:24.744 > [DPL] targeting 0 W, base load is 200 W, power meter reads -167.9 W (valid)
11:23:24.881 > [DPL] inverter 114184518511 is behind power meter producing 43 W
11:23:24.948 > [DPL] requesting 0 W from 1 solar-powered inverter currently producing 43 W (diff -43 W, hysteresis 5 W)
11:23:24.999 > [DPL] will cover 43 W using 1 solar-powered inverter
11:23:25.064 > [DPL] battery allowance is 0/0 W DC/AC, solar power is 0/0 W DC/AC, requested are 0 W AC
11:23:25.126 > [DPL] requesting 0 W from 0 battery-powered inverters currently producing 0 W (diff 0 W, hysteresis 5 W)
11:23:25.188 > [DPL inverter 114184518511]:
11:23:25.254 > solar-powered, producing 43 W
11:23:25.313 > lower/current/upper limit: 50/49/600 W, output capability: 600 W
11:23:25.377 > sending commands enabled, reachable, eligible
11:23:25.442 > max reduction production/standby: 0/0 W, max increase: 0 W
11:23:25.505 > target limit/output/state: -1 W (unchanged)/43 W/unchanged, 0 update timeouts
11:23:25.565 > MPPTs AC power: a: 21 W b: 23 W
11:23:25.732 > Success

Vielen Dank für Eure Hilfe :)

[schlimmchen]

Weiter in #1609.