ADB5800 uImage

[puzola]

OV image type

Enigma2 (e2)

OV version

7 (Python 2.7)

OV revision

rxxx (7)

STB name

adb_box 5800s

Describe the bug and expected behavior

Hello !!
"Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)"
Please modify the uimage configuration
nand start doesn't work, it only boots from usb
correct nand kernel configuration sample "audioniek E2 buildsystem"
THX

Steps to reproduce

No response

Enigma2 logs

NAND read: device 0 offset 0x3c00000, size 0x300000

Reading data from 0x3effe00 -- 100% complete.
 3145728 bytes read: OK
## Booting image at a5000000 ...
   Image Name:   Linux-2.6.32.71_stm24_0217
   Image Type:   SuperH Linux Kernel Image (gzip compressed)
   Data Size:    2158005 Bytes =   2.1 MiB
   Load Address: 84001000
   Entry Point:  84002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel console=ttyAS0,115200 root=/dev/mtdblock0 rw rootfstype=jffs2 mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 nwhwconf=device:eth0,hwaddr:00:03:91:88:76:25 init=/bin/devinit - 0x00000000 - 0 ...

Linux version 2.6.32.71_stm24_0217 (gcc version 4.9.4 (GCC) ) #1 PREEMPT Mon Jan 11 22:36:20 CET 2020
Boot params:
... MOUNT_ROOT_RDONLY - 00000001
... RAMDISK_FLAGS     - 00000000
... ORIG_ROOT_DEV     - 00000200
... LOADER_TYPE       - 00000000
... INITRD_START      - 00000000
... INITRD_SIZE       - 00000000
Booting machvec: STb7100 Reference board
Node 0: start_pfn = 0x4000, low = 0xc000
Zone PFN ranges:
  Normal   0x00004000 -> 0x0000c000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00004000 -> 0x0000c000
STMicroelectronics STb7100 Reference board initialisation
STx7100 version 3.x
bpa2: partition 'LMI_VID' created at 0x10800000, size 57344 kB (0x03800000 B)
bpa2: partition 'LMI_SYS' created at 0x044ae000, size 28672 kB (0x01c00000 B)
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: console=ttyAS0,115200 root=/dev/mtdblock0 rw rootfstype=jffs2 mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 nwhwconf=device:eth0,hwaddr:00:03:91:88:76:25 init=/bin/devinit
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
PVR=04061100 CVR=30480000 PRR=00009100
I-cache : n_ways=2 n_sets=256 way_incr=8192
I-cache : entry_mask=0x00001fe0 alias_mask=0x00001000 n_aliases=2
D-cache : n_ways=2 n_sets=512 way_incr=16384
D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
Memory: 97364k/131072k available (2660k kernel code, 870k data, 112k init)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:600
console [ttyAS0] enabled
sh_tmu: TMU0 used for clock events
sh_tmu: TMU0 used for periodic clock events
sh_tmu: TMU1 used as clock source
Calibrating delay loop... 264.19 BogoMIPS (lpj=528384)
Mount-cache hash table entries: 512
CPU: STx7100
devtmpfs: initialized
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
DMA: Registering DMA API.
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource TMU1
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Installing knfsd (copyright (C) 1996 [email protected]).
Slow work thread pool: Starting up
Slow work thread pool: Ready
JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
fuse init (API version 7.13)
msgmni has been set to 190
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
lirc_dev: IR Remote Control driver registered, major 61
lirc-stm: probe found data for platform device lirc-stm
lirc-stm: STM LIRC plugin using IRQ 125 in IR mode
lirc_dev: lirc_register_driver: sample_rate: 0
STMicroelectronics LIRC driver initialized.
STMicroelectronics ASC driver initialized
stm-asc.0: ttyAS0 at MMIO 0x18032000 (irq = 121) is a stm-asc
stm-asc.1: ttyAS1 at MMIO 0x18033000 (irq = 120) is a stm-asc
loop: module loaded
MiPHY driver style MiPHY-DUMMY probed successfully
MiPHY-DUMMY, c0.0 Claimed by sata-stm
scsi0 : sata-stm
ata1: SATA max UDMA/133 irq 170
physmap platform flash device: 00200000 at 00000000
physmap-flash: Found 1 x16 devices at 0x0 in 16-bit bank
NOR chip too large to fit in mapping. Attempting to cope...
Support for command set 0003 not present
gen_probe: No supported Vendor Command Set found
physmap-flash physmap-flash: map_probe failed
smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre <[email protected]>
ata1: SATA link down (SStatus 0 SControl 0)
eth0: SMC91C11xFD (rev 2) at a0c00000 IRQ 5 [nowait]
eth0: Ethernet addr: 00:00:00:00:00:00
eth0: Invalid ethernet MAC address.  Please set using ifconfig
nwhw_config: (eth0) setting mac address: 00:03:91:88:76:25
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
stm_usb_probe: usb_48_clk clock not found for stm-usb.0
stm_usb_probe: usb_phy_clk clock not found for stm-usb.0
stm-ehci stm-ehci.0: STMicroelectronics EHCI Host Controller
stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1
stm-ehci stm-ehci.0: irq 169, io mem 0x191ffe00
stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
stm-ohci stm-ohci.0: STMicroelectronics OHCI Host Controller
stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2
stm-ohci stm-ohci.0: irq 168, io mem 0x191ffc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
i2c /dev entries driver
i2c_st40_pio: ST40 PIO based I2C Driver for STM24
Linux video capture interface: v2.00
sh_tmu: TMU0 kept as earlytimer
sh_tmu: TMU1 kept as earlytimer
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
STMicroelectronics - Coprocessors st231 Init
st231.0 Coprocessor -------------------------------------------
    flags 0001 RAM start at 0xb0000000  size      0x00400000
                  cop. addr 0x10000000
    Channels : Not defined
    IRQ      : not used
---------------------------------------------------------------
st231.1 Coprocessor -------------------------------------------
    flags 0001 RAM start at 0xb0400000  size      0x00400000
                  cop. addr 0x10400000
    Channels : Not defined
    IRQ      : not used
---------------------------------------------------------------
DMA: Registering fdma_dmac handler (16 channels).
IRQ 140/fdma_dmac: IRQF_DISABLED is not guaranteed on shared IRQs
stm-fdma stm-fdma: firmware: using built-in firmware fdma_STx7100_0.elf
stm-rng hardware driver 1.0 configured
platform fdma_dmac: SLIM hw 0.0, FDMA fw 3.1
Advanced Linux Sound Architecture Driver Version 1.0.21.
ALSA device list:
  #0: STMicroelectronics STx7100 cut 3.x SOC audio subsystem
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
Root-NFS: No NFS server available, giving up.
VFS: Unable to mount root fs via NFS, trying floppy.
List of all partitions:
No filesystem could mount root, tried:  jffs2
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)

Screenshot

No response